61 visiting now: 23 China China flag 15 France France flag 15 USA USA flag 2 Korea Korea flag 1 Afghanistan Afghanistan flag 1 Romania Romania flag 1 Sweden Sweden flag 1 Czech Republic Czech Republic flag 1 UK UK flag 1 Germany Germany flag

How To Use C44 Roof Desk Forming Machine - China

price: contact company for price

How to use C44 roof desk forming machineC

C44 shingle molding machine is the majority of users a

molding equipment, but its time to use the correct method of


1.C44 shingle molding machine operation, to check whether

the connection is solid throughout, installing bolts, nuts

are tightened, so the chassis lubrication should add enough

oil to power-up test machine, the first empty running

carefully observed, with or without vibration , noise, oil

window is to oil, the components are coordinated motion,

everything works before installing the mold.

2 Install C44 shingle molding machine mold, you must cut

off the power manually moving belt or gear motor, so that

the table indexing, and to rise to the highest point of

sliding seat, preferably with an object supported on the

bench and between the bottom slide to slip seat naturally

fall, causing the accident.

3.C44 shingle molding machine equipment the first row and

the last row to find a good center, then tighten lock nut on

both sides, in the middle of the center wheel front and rear

lay a straight line, the upper and lower shaft after

adjusting the gap , you can adjust the machine along a

straight line.

4 first arc C44 glazed roof desk forming machine tile press

machine equipment before and after the two corners line up

the shaft from the large end of the height of the frame in

the end the amount of the same, and then routed to the last

row from the first, to find a line drawing straight, check,

whether the lower shaft in a straight line, the lower shaft

left and right sides tune into levels. Tile press platen

deviation debugging methods, such as to the right to run,

pad left corner, or off the right side of the bottom level,

the first of several shaft axis deviation Ladi few flat

bottom, with the bottom of the upper shaft axis whereabouts.

Company Contact:

  • Phone: 863178312992

  • Address: 104 National Road, Botou, cangzhou, China

  • Email: Email

Published date: August 25, 2013 -

  • Business Description: Botou Xinnuo molding machine limited company is a supplier of roof plate

    roll forming achine,sandwich plate roll forming machine,floor plate roll

    forming machine, bending machine, shearing machine, cutting

    machine,double roll forming machine,C type steel,Z steel,light steel

    keel machine and so on,is a large scale technology quality


    Roll forming machine, floor deck roll forming machine, double roll forming machine

Related listings

  • Jct Reactor Tank
    Jct Reactor Tank
    Manufacturing - Foshan JCT Machinery Co., Ltd - China - May 20, 2016 - contact company for price

    1. Simple Description JCT reactor tank: 1) . Different capacity design from 50L to 50, 000L. stirred mixing reactor 2) . Made of stainless steel 304/ 316L, or other material ( decide by client) . 3) . Have jacket and coil- pipe style. stirred mixing ...

  • Selling All Models Of Pto Hydraulic Pumps
    Selling All Models Of Pto Hydraulic Pumps
    Manufacturing - A&S Hydraulic Co., Ltd - China - May 17, 2016 - contact company for price

    A& S Hydraulic Co. , Ltd supplies all models of PTO Hydraulic Pumps: PTO Hydraulic Pump HC- PTO- 1A PTO Hydraulic Pump HC- PTO- 2A PTO Hydraulic Pump HC- PTO- 3A PTO Hydraulic Pump HC- PTO- 7A PTO Hydraulic Pump HC- PTO- 8A PTO Hydraulic Pump HC- PTO...

  • 8 Mm Container Bolt Seal
    8 Mm Container Bolt Seal
    Manufacturing - Shandong Tengxin Seal Co., Ltd - China - May 17, 2016 - contact company for price

    High Security bolt seal with ABS covered and ' H' stamped at the bottom is a special locking device. It can be used on shipping container, truck and trailer doors and where high security tampering evidence is required. Various colors to choose. C- TP...

Safe Trade Tips

  • Ask for business references and check them
  • Use a payment method that offers better protection for all such as Letters of credit and verified professional escrow services. Avoid payments in advance such as money transfers
  • Verify their business via their local Chamber of Commerce
  • Search the internet using their website address, their business name, their phone and fax numbers, and their email addresses to see if you can find any feedback about them.
  • Get to know more about scams to avoid: Internet Crime Complaint Center - International Financial Scams
  • This site is never involved in any transaction, and does not handle payments, shipping, guarantee transactions, provide escrow services, or offer "buyer protection" or "seller certification"