Rotary Kiln Pinion Wheel Installation Process - Chinaprice: contact company for price
the gearbox output shaft. Large ring meshes with the rotary
kiln gear which drive the pinion. Pinion installation and
maintenance and the drive shaft alignment is very important.
Installation, to initial positioning tooth tip clearance.
1. Determination of tooth tip clearance
The gear tooth tip clearance c = 0. 25M (where M is
modulus gear). Rolling circle and supporting rolle for long-
term wear and tear due to high temperature can cause the
whereabouts of the rotary kiln cylinder and a large gear
ring radial runout and other factors. Addendum must be
necessary to increase the gap - Recommended for large rotary
kiln c = 0.28M (where the ground round modulus M).
2. Installation process
(1) Find the tooth tip clearance to the initial position.
Length of the bar can be slightly larger than the width of
the pinion gear on the two clenched between the top of the
root.Then complete the localization of small gear.Next
adjust the tooth surface at both ends of the parallel degree
of backlash and as you can. Simultaneous measurement of gear
backlash must meet the requirements.
(2) General pinion ring gear is wider than the body width
of the rotary kiln. Difference should be equal to the width
of the cylinder runout. So should run up and down rotary
kiln position in which it is set to wide-tooth contact
position. To achieve the normal operation of the rotary kiln
thermal process. Large and small gear longitudinal
(3) directly to the two gear pitch circle tangent method to
install. Although this approach that the large thermal
expansion of the ring gear. The tire inflation would raise
the kiln shell. It does not result in changes in gear
meshing. The introduction of the rotary kiln is currently
(4) The current small gear installed in two ways: when a
small gear, gear shaft, bearing, steel base has been
installed by the manufacturer together. Direct alignment
with a small gear, the overall installed in place when the
parts in bulk to the scene. It is required with the order
after the assembly. The overall look is in place.
3. the technical requirements of rotary kiln pinion
(l) pinion installation design requirements should allow
the expansion of a large amount of gear. And determine its
pitch to meet the requirements.
(2) adjusting the determination of the size of the gear
tooth tip clearance. It can be 0. 28M or o. 25M + (2 ~ 3) mm
total take (M for the gear module.)
(3) meshing well, the direction of the contact surface
in the tooth should not be less than 50%. In the tooth width
direction of not less than 65%;
(4) Link the pinion shaft and speed reducer shaft
together. Reducer motor coaxial with the main error is not
greater than 0.2mm.
http://www.shzbm.com rotary kiln
http://www.pe750.com jaw crusher
http://www.pe600.com ball mill
http://www.mining-ss.com rotary kiln
http://www.machine-ss.com ball mill manufacture
- Posted By: Jiangsu zhongbo Heavy Machinery
- Phone: 862150115838
- Address: No.999 Gangxi road, haimen, China
- Website: http://www.machine-ss.com
Published date: March 27, 2013 -
- Business Description: Dating from a state designated factory by National Construction Department, Jiangsu Zhongbo Heavey Industry Co., Ltd, has a history of over 30 years history of machine manufacture. It is a professional manufacturer of crushing and powder making equipment and beneficiation equipment. It is a major production and export base of mining machinery in China.
Till now, we have formed a whole production chain with main products: crushing machinery, grinding machinery, and auxiliary products: vibrating screen, vibrating feeder and other associated equipments. Products cover more than 20 models of 3 major series: mill series, crushing series, and sand making series. Advanced technology content, high reliability, low operation and maintenance cost have enabled our products to take the leading position in the field. All the products are qualified the national patent and have successfully achieved ISO9001:2000 Quality Management Certificate and EU CE Certificate.
Jct Reactor TankManufacturing - Foshan JCT Machinery Co., Ltd - China - May 20, 2016 - contact company for price
1. Simple Description JCT reactor tank: 1) . Different capacity design from 50L to 50, 000L. stirred mixing reactor 2) . Made of stainless steel 304/ 316L, or other material ( decide by client) . 3) . Have jacket and coil- pipe style. stirred mixing ...
Selling All Models Of Pto Hydraulic PumpsManufacturing - A&S Hydraulic Co., Ltd - China - May 17, 2016 - contact company for price
A& S Hydraulic Co. , Ltd supplies all models of PTO Hydraulic Pumps: PTO Hydraulic Pump HC- PTO- 1A PTO Hydraulic Pump HC- PTO- 2A PTO Hydraulic Pump HC- PTO- 3A PTO Hydraulic Pump HC- PTO- 7A PTO Hydraulic Pump HC- PTO- 8A PTO Hydraulic Pump HC- PTO...
8 Mm Container Bolt SealManufacturing - Shandong Tengxin Seal Co., Ltd - China - May 17, 2016 - contact company for price
High Security bolt seal with ABS covered and ' H' stamped at the bottom is a special locking device. It can be used on shipping container, truck and trailer doors and where high security tampering evidence is required. Various colors to choose. C- TP...
Safe Trade Tips
- Ask for business references and check them
- Use a payment method that offers better protection for all such as Letters of credit and verified professional escrow services. Avoid payments in advance such as money transfers
- Verify their business via their local Chamber of Commerce
- Search the internet using their website address, their business name, their phone and fax numbers, and their email addresses to see if you can find any feedback about them.
- Get to know more about scams to avoid: Internet Crime Complaint Center - International Financial Scams
- This site is never involved in any transaction, and does not handle payments, shipping, guarantee transactions, provide escrow services, or offer "buyer protection" or "seller certification"