Exterior Durable Polyester Powder Coatings With Antimicrobial Technology Mt 610 Am - China

Product description

MT-610 AM is a range of polyester TGIC Free powder coatings designed for exterior exposure with good weather resistance from just one application with specific antimicrobial activity.

The coatings sustain a longer lifespan and are available in a wide range of colors and finishes which allow your product to shine.

Additionally, MT-610 AM uses antimicrobial technology to reduce the number of microbes such as bacteria and mold.

Test results have proven a reduction of bacteria and mold up to 99.9%.

MT-610 AM offers not only beautiful aesthetics but also a performance to match.

It is ideally suited to a broad range of outdoor applications including outdoor furniture, playground equipment, signs, fencing, vending machines and general metal finishing.

Can also be used for indoor application if required.

Powder properties Typical value

Chemical Type Polyester – TGIC Free

Density 1.2 – 1.9 g/cm³, depending on colour and effect

Recommended film thickness 60 – 90µm

Shelf life 24 months below 30 °C 12 months below 35 °C Storage Conditions Under dry, cool (≤ 30°C) conditions (open boxes must be resealed) Curing schedule 30-40 min at 170°C 10-20 min at 180°C 8-16 min at 200°C (at object temperature) Pre-treatment

Galvanised steel requires surface preparation by either multi-stage pretreatment using either zinc phosphate or chromate conversion or controlled sweep blasting.

Depending on the type of galvanizing, degassing or use of anti-bubbling additives may be required – follow the procedural advice of the pretreatment supplier.

Iron phosphate and particularly Zinc phosphating of ferrous metals improves corrosion resistance.

Aluminium substrates may require a chromate conversion coating.

Application

Powders can be applied by manual or automatic electrostatic spray equipment.

A good protection is linked with the recommended film thickness.

All powders can show small color differences from batch to batch, this is normal and unavoidable.

Applicators and fabricators are advised to use a single batch for parts that will be assembled together.

Differences are more likely with special effect powders.

Bonded products have better application properties than blended products (more stable) but attention should still be paid to line settings in order to avoid “marble effect” and changes in aspect after recycling.

Different substrates (aluminium, steel, galvanized steel…), use of primer, and big changes in film thickness may give a different aspect.

Products with different codes should not be mixed even if same colour and gloss.

It is recommended that for consistent application and appearance product be fluidized during application.

Test conditions

Actual product performance will depend upon the circumstances under which the product is used.

Testing has been determined under laboratory conditions using the following application properties and is for guidance only.

Pre-treatment Zinc Phosphate

Substrate Polished steel

Curing schedule 10 min at 200°C

Film Thickness 60 – 70µm

Mechanical tests Typical value Method/standard

Adhesion Class 0 ISO 2409 (2 mm Crosshatch)

Erichsen cupping Pass 5 mm ISO 1520

Flexibility Pass 5 mm ISO 1519

Hardness Pass – no penetration to substrate ISO 1518-1 (2000g)

Impact resistance Pass 2.5 Joules reverse & direct (20 in lb) ISO 6272-2 (d/r)

Company Contact:

• Posted By: Standard International Group (HK) Limited

• Phone: +86-21-64208466-808

• Address: Floor 2, #47 Building, 280 Jiugan Road, Songjiang district, Shanghai, China, Shanghai , Shanghai , China

• Email:

• Website: https://moutainchem.com/

• Business Description: Standard International Group (HK) Limited was founded in 2003 - Over years, Standard Group has established long-term strategic cooperative relations with many well-known industrial chemical manufacturers, such as Sherwin-Williams, LANXESS, Evonik, Covestro, Elementis and so on, thus ensuring that customers can receive consistent high-quality services.
  
  Years of professional accumulation make us not only provide high-quality industrial coating additives, but also medicine Pharmaceutical Intermediates and electronic chemistry.
  
  From the painting plant laboratory first sample testing, middle-testing and final-testing, we adhere to the professional, sincere, enthusiastic and efficient service concept, our technical team always adjust the sample during different testing process until it performs perfect chemical reaction at customer’s paints.