3flybacksbr 130w Co2 Laser Power Unit - China

BR-130W CO2 laser power supply

Feature

1 - The 220/110V CO2 power supply's control is applicable to high/low level signal.

TTL level is to control the on/off of the laser power with a protective switch to check water-flow and ventilation.

2 - The 130W CO2 power supply can match with EFR, Yongli, SPT, Weiju and other factories'160-165cm 130W sealed glass type CO2 laser tube.

The 220/110V CO2 power supply uses zero-current half-bridge soft-switch circuit to make sure the CO2 power supply on laser cutter has high efficiency and fast response speed.

3 - The CO2 power supply on laser cutter is well grounded, which can ensure the safety of operators.

At the same time, the 220/110v CO2 power supply also has an open circuit protection function, which allows the CO2 power supply on laser cutter to work for a short time in the open circuit state.

4 - The 130W CO2 power supply has RED TEST button to easily figure out CO2 power supplies or CO2 laser tube's failure.

It is very easy and simple to remove trouble.

5 - Input analog signal(0~5V) or PWM is used to control the output laser power on this 130W CO2 power supply

6 This130W CO2 power supply is equipped with two cooling fans.

Better heat dissipation can protect the internal electronic components of this power supply

7 - Each CO2 power supply on laser cutter before selling will go through the aging check:

(1) sustain 10 hours at temperature 60 Degrees Celsius under full-load condition;

(2) 500 times on/off check for 7 seconds.

8 - The 220/110V CO2 power supply has H/L/P/G/IN/5V control signal port, The upper cover and bottom shell are aluminum shell is galvanized sheet.

9 - The 130W CO2 power supply can use an external LCD module.

It can display common fault codes, output current and working status.

It is helpful for operators to understand the working state of 220/110V CO2 power supply and solve problems quickly.

In addition, the output current can also be changed by the rotating potentiometer of the LCD module.

Specification

Input Input voltage AC220V±10% (AC110V specified while order) AC frequency 47~440HZ Maximum input power 970W Maximum input current 4.3A

Output Maximum output voltage 40KV Maximum output current 36mA

(depending on the laser tubes of different manufacturers)

Efficiency More than 90% (Full load)

Response speed Not more than 1ms

Control lnterace TTL multilevel switching control, effective level can be high and low selection (see control wining diagram)

Insulation lnput-output AC 1500V 1 minutes not more than 10mA lnput-shell AC 1500V 1 minutes not more than10mA Output-shell Connection

Open Circuit Protection Can be short circuit (requires a good grounding shell, while avoiding the positive electrode and the shell between the arc)

Environmental Requested Working temperature -10℃~50℃ Storage of temperature -20℃~75℃ Relative Humidity Maximum 85%RH (non-condensing) Altitude 100, 000 feet of work

200, 000 feet of storage, dose not work

Cooling methods Forced air cooling (fan cooling)

Dimensions (LxWxH) 335mmx205mmx100mm

Company Contact:

• Posted By: Jinan Ruby Laser Technology Co.,Ltd

• Phone: 13295411923

• Address: 8510 Room.Huiju Building.intersection of West Second Ring Road and Meili Road,Tianqiao District, Jinan , Shandong , China

• Email:

• Website: https://www.rlaserpowersupply.com/

• Business Description: Jinan Ruby Laser Technology Co.,Ltd is main laser power supply manufacturer which was established at 2015 - From then on ,it has more than 10 years experience to research & develop, produce and sell RUBYLASER brand CO2 laser power supply,YAG pulsed xenon lamp power supply and special power supplies for UV/RF CO2 laser marking machine.
  
  At present, our laser power supply has four series products(ZS series,ESseries,RS series and ICO series).
  
  ZS series laser power supplies are used for CO2 laser tube,ES series laser power supply is for UV laser marking machine,RS series laser power suppply is for RF CO2 laser marking machine and ICO series laser YAG pulsed exnon lamp power supply is used on laser welding machine for jewelry welding or mold repair.
  
  Based on client’s using feedback and’ innovation in electronic technology,the company developed LCD display screen for CO2 laser power supply.
  
  Now ZS series power supply has 40W/50W/60W/80W/100W/150W /200W/300/450W models and ICO series power supply has 80W/100W/200W/400W single or double lamps model.
  
  Since its establishment,Jinan Ruby Laser Technology Co., Ltd attaches great importance to the quality of laser power supply to establish RUBYLASER brand’s good reputation in domestic and foreign markets In order to realize this goal, it has an experienced management team and skilled technical workers.
  
  And all accessories are purchased from United States, Japan,France, Taiwan and China’s well-known companies, some electronic components have UL,CE,CCC,TUV,SA certification.
  
  The laser power supplies are also produced accordance with the requirements of ISO9001 quality system.
  
  At present, all CO2/YAG laser power sources have obtained CE certification, and they are used by the main laser engraving machine, laser cutting machine,laser marking machine and YAG laser welding machine manufacturers.
  
  Excellent quality, reasonable price and professional pre-sale and after-sales service team make RUBYLASER power supply become one of three great power supply manufacturers in China.
  
  RUBYLASER CO2 lase power source’s feature,specification,ins tallation size, operation method and wiring connection method are completely same with other brands' power supplies, so PS sereis laser power supply can replace these three brands power supplies.
  
  Now Jinan Ruby Laser Technology Co., Ltd 's laser power supply have occupied about 30% of the Chinese market
  
  .